Cr2O3 doping effect on silica glass cooling rate

doi:10.21203/rs.3.rs-2219420/v1

Download PDF

Research Article

Cr2O3 doping effect on silica glass cooling rate

https://doi.org/10.21203/rs.3.rs-2219420/v1

This work is licensed under a CC BY 4.0 License

Journal Publication

published 29 Dec, 2022

Read the published version in Silicon →

You are reading this latest preprint version

In this paper we present the results on the effect of the SiO₂ melt cooling rate on the morphology of its surface. The method of atomic force microscopy explores a surface roughness of the silica glass cooled at different rates after its heating up to more than 2100 ^оС. The study compares three modes of cooling glass rods with a diameter of 14 mm: convective heat exchange with the surrounding air, quenching with dropping the sample into a vessel with water, and radiation of silica glass doped with 0.1 % Cr₂O₃. The surface roughness of silica glass in the second and third modes of cooling was significantly less than in the conditions of convective heat exchange. Doping the silica glass with Cr₂O₃ increases the heat exchange coefficient by 2 times and decreases the surface roughness. The results of the research can contribute to improving the mechanical and optical properties of silica glass light guides.

Silica glass

Heat exchange

Radiation

Cooling

Roughness

Strength

Silica glass (SG) has a unique high strength, which is equal to 22-44 GPa according to theoretical forecasts [1]. Therefore, silica fibers are promising reinforcing filler for lightweight high-strength composite structural materials. However, despite various methods of such fiber production, their strength does not exceed 6 GPa [2]. Works [3-7] consider the factors constraining the development of the processes to obtain fibers with strength close to the theoretical level for SG.

As known, cracks on glass surface initiate its destruction [8,9]. In [10], it is assumed that temperature fluctuations can generate cracks, leading to decrease in the SG strength by 2 times compared to its theoretical estimate.

The strength of commercial optical fiber made of SG with a diameter of 125 microns (6 GPa) corresponds to the depth of a critical surface crack ≈ 6 nm, calculated based on experimental dependence (1) of fiber strength (σ) on defect size (r) on its surface [5]:

σ = D/r^0.5,(1)

where D is a constant ≈ 0.474 × 10^‒3 GPa⋅m^0.5.

Extrapolation of equation (1) to the defect size equal to the length of the Si−O bond of the SG grid (0.16 nm) gives a strength value equal to 37.5 GPa, corresponding to theoretical estimates [1]. Experimental studies [5] showed that the strength of particularly thin SG fibers with a diameter of 120 nm, measured at natural ambient humidity, is equal to 26 GPa. The globular nature of the glass structure [11-13] can determine the specifics of its surface morphology and regularity of distribution of nanoscale cracks in depth. Therefore, the high strength of particularly thin silica fiber may result from the decrease of SG surface roughness due to its high cooling rate when drawing the fiber [14, 15].

Thus, the high cooling rate of the fiber in comparison with the preform leads to a decrease in the surface roughness of the SG [16]. At the same time, water quenching of the preform heated to 2300 ^oC reduces the level of its surface roughness by 10 times due to the high cooling rate compared to cooling in air [17]. However, such a SG cooling method cannot be implemented in the process of fiber drawing. Therefore, this work aims to study the effect of different cooling conditions on the SG surface roughness measured by atomic force microscopy (AFM).

According to Kirchhoff's radiation law, heated bodies lose thermal energy due to radiation; its spectral region corresponds to the wavelength of absorption by this substance. Silica glass at high temperatures is transparent in the optical spectrum of the visible range [18]. However, in this spectral region the SG impurities of transition metals intensively absorb radiation [19] and hence they effectively emit, reducing the temperature of SG.

As known [19], SG containing a Cr admixture has the greatest absorption capacity compared to other coloring impurities: Ni, V, Co and Fe (Table 1). Therefore, intentional additions of Cr₂O₃ to silica glass should be expected to provide the greatest effect of its cooling due to radiation in the visible range of the optical spectrum.

Table 1 SG absorption (α) at 600 nm wavelength with impurity content of 10^-7 wt% [19]

Impurity	Ni	Cr	V	Co	Fe
α, dB/km	0.5	3.5	2.2	2.5	0.4

For experiments, samples were SG rods with a diameter of 14 mm. A core with a diameter of 5.5 mm was obtained by melting quartz grit inside a KV glass tube. In sample No. 1, the core was made of pure silica glass, and in sample No. 2 it contained 0.1 wt% Cr₂O₃.

A SG rod rotating at a speed of 45 revolutions per minute was heated by the flame of an oxygen-hydrogen burner using an automated system OFC-12-729 manufactured by Nextrom. The surface temperature of the samples was measured with a standard optical pyrometer at a radiation wavelength of ≈ 5 microns. In this region of the optical spectrum, SG is not transparent [20].

After reaching a constant temperature value at maximum power of the burner, it was turned off. The samples were cooled under two different conditions:

- during the heat exchange of samples with the ambient air;

- discharging of sample No. 1 (for no more than 1 second) into a vessel with water.

The SG surface roughness was studied using an AFM Solver PRO-M (NT-MDT, Russia). The measurements were made by the contact method using the ETALON tip with the curvature radius less than 10 nm. A horizontal resolution is better than 20 nm, and vertical resolution is about 0.1 nm.

The experiments have shown that the steady-state surface temperature of a sample heated by a flame stream is significantly affected by the radiation of the core glass in the visible transparency region of SG. Thus, the addition of 0.1% Cr₂O₃ in the SG core reduces the surface temperature of the sample at maximum burner power from 2300 to 2175 ^oC (Fig. 1). The cooling time of sample No. 2 doped with Cr from the maximum heating temperature to 1000°C (30 s) is two times less than that of sample No. 1 of pure SG (60 s).

Figure 2 shows a diagram of heat flows while cooling sample No. 2, where, in comparison with sample No. 1, heat flow QR_c is added to the radiation from the core into the environment. It should be noted that the heat flow to radiation from the SG surface (QR) is significantly less than the heat flow to radiation from the core (QR_c) doped with chromium oxide. This occurs in accordance with Wien's law, the maximum radiation energy with a body temperature increase shifts to the short-wave region of the optical spectrum, in which Cr in the wavelength region of 600-800 nm has the greatest emissivity. The melt of pure SiO₂ emits in the long-wavelength region of the optical spectrum (at a wavelength of more than 2000 nm [20]), while remaining transparent to the radiative flow from Cr₂O₃.

The measurement results of the SG surface relief on AFM (Fig. 3) showed that:

- the roughness of the water quenching sample No. 1 is significantly less than with the convective heat exchange with the surrounding air;

- comparison of the samples surface roughness indicates the same cooling rate of SG both for the conditions of its quenching in water and due to the emissivity of chromium.

Fig. 4 shows the shapes of the bulb under the same drawing conditions in a furnace with a graphite heater of 125 microns fiber diameter from samples No. 1 and 2. The length of the bulb doped with Cr₂O₃ is significantly less than that of a bulb made of pure SG. This is due to the different values of the heat transfer coefficient from the heated sample to the environment.

Based on the distribution of diameter (d) along length (z) in the bulb zone, it is possible to calculate the constant (B) [21] proportional to the heat transfer coefficient during SG cooling of according to equation (2):

ln ln (d/d_f) = ln ln (d_O/d_f) - Bz, (2)

where d_f is the fiber diameter equal to 0.125 mm; d₀ is the normalized diameter ≈ 5 mm.

Constant B is determined by the slope of straight lines for dependence ln ln (d/df) on the z coordinate along the axis of the bulb (Fig. 5). The ratio of this constant value for two samples is ≈ 2, which indicates a significant increase in the heat transfer coefficient when alloying the core with chromium. Therefore, the cooling time up to 1000 ^oC for samples No. 1 and 2 differs twice (Fig. 1).

It is obvious that the shape of the bulb and its surface relief, depending on the cooling rate of the SG, is determined both by the Cr₂O₃concentration and thickness of the cladding.

The paper shows a significant dependence of the SG surface roughness on its cooling rate. The height of the relief peaks of the SG cooled in the air atmosphere is 7 nm, while at water glass quenching and chromium radiation cooling the profile peaks do not exceed 1.5 nm.

Previously, it was found that defects in the surface of silica fiber that reduce its strength [22] are usually caused by the presence of micro-admixture of coloring elements (Cr and Fe). Their high emissivity leads to local cooling and an increase in the SG viscosity, which prevents its plastic deformation. Therefore, the size of such defects does not change in the process of fiber drawing, which determines its low-strength state. The presence of a chromium-doped radiating SG can prevent such behavior of localized defects containing coloring impurities. The cooling rate increase also contributes to the hardening of the high-temperature homogeneous state of the doped silica glass, which is prone to liquation. In the technology of the active light guides doped with rare earth elements (Er, Yb, etc.), it can lead to a decrease in optical losses.

The optimization of Cr₂O₃concentration and preform design, aimed at improving the cooling efficiency of SG, can lead to an increase in the strength of the silica fiber. This opens up prospects in the creation of high-strength fiberglass composite materials reinforced with such fibers. A high strength-to-weight ratio of such materials ensures the progress in a number of industries, especially in the construction industry, machine tool manufacturing and space technology.

The research results indicate a significant influence of the cooling rate of the SG heated to more than 2000 °C on its surface relief. It is shown that an increase in the emissivity of glass in the visible region of the spectrum due to Cr₂O₃ doping doubles the cooling rate and smooths its surface roughness.

This behavior of SG is probably due to the specifics of the globular structure of the glass matrix, which affects both the surface morphology and structure of the silicon dioxide melt in a quenched state. Therefore, the cooling rate of the SG heated to more than 2000 °C can affect both the strength and optical properties of products based on it.

Consent to participate. All authors agreed to participate in the authorship of the manuscript.

Consent for publication. All authors gave their consent to publish the manuscript.

Availability of data and materials. the authors of the manuscript declare the availability of the data and materials of the manuscript.

Conflict of interest. The authors declare that they have no financial or non-financial conflict of interest.

Acknowledgements. The authors are thankful to Academician of the Russian Academy of Sciences, Professor V. G. Peshekhonov for supporting this work.

Author Contributions

All authors contributed to the study conception and design. Material preparation, data collection and analysis were performed by P.S. Parfenov, I.K. Meshkovskiy, A.Yu. Kulesh and A.A. Untilov. The first draft of the manuscript was written by M.A. Eronyan. All authors commented on previous versions of the manuscript. All authors read and approved the final manuscript.

Funding

This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.

Ethical Statement

The authors assure that: the described work has not been previously published elsewhere; it is not being considered for publication elsewhere; the publication has been approved by all co-authors and responsible persons at the institutions where the work was done; all sources used are properly disclosed; all authors have been personally and actively involved in substantial work leading to the paper, and will take public responsibility for its content.

Wiederhorn SM (1969) Fracture surface energy of glass. J Am Ceram Soc 52:99–105. https://doi.org/10.1111/j.1151-2916.1969.tb13350.x
Dimarcello FV, Brownlow DL, Huff RJ and Hart Jr AC (1985) Multikilometer lenghths of 3.5 GPa (500 kci) prooftested fiber. J lightw technol LT 3: 946-949. https://doi.org/10.1109/JLT.1985.1074314
Sakaguchi S, Nakahara M, Tajima Y (1984) Drawing of high-strength long-length optical fiber. J Non Cryst Solids 64:173–183. https://doi.org/10.1021/acs.cgd.5b00253
Eron'yan MA, Zlobin PA, Kozlova MA, Levit LG, Romashova EI, Khokhlov AV and Tsibinogina MK (2006) Influence of the physicochemical state of impurities on the strength of silica fibers. Glass Phys Chem 32:623–628. https://doi.org/10.1134/S1087659606060058
Brambilla G. and Payne DN (2009) The ultimate strength of glass silica nanowires. Nano Letters, 9 831–835. https://doi.org/10.1021/nl803581r
Kulesh AY, Eronyan MA, Meshkovskii IK, Zolotarev VM, Bisyarin MA, Tsibinogina MK (2015) Crystallization of silica glass fibers during the drawing process. Crystal Growth and Design 15:2831-2834. https://doi.org/10.1021/acs.cgd.5b00253
Kulesh AY, Eronyan MA, Meshkovskii IK, Parfenov PS and Tsibinogina MK (2017) Influence of mechanically stimulated hydrolysis on static fatigue and strength of silica optical fiber. Strength, Fracture and Complexity 10:39–47. https://doi.org/10.3233/SFC-170199
Griffith AA (1920) Phenomena of rapture and flow in solids. Phil. Trans. Roy. Soc. (London) 221A:163-198. https://doi.org/10.1098/rsta.1921.0006
Elliot HA (1947) Analysis of the condition for rupture due to Griffith cracks. Proc. Phys. Soc. (London) 59, Pt. 2:208-223. https://doi.org/10.1088/0959-5309/59/2/305
Hilling WB (1962) Modern Aspects of the vitreous state, 2, Butterworth & Co. Ltd., London.
Dolapchi SM and Denisova OA (2017) Globules and their internal structure. Elektrotekh. Inform. Kompleksy Sist.13:106–111.
Kozlova MA, Shkonda PA (1987) The Surface structure of silica glass and silica subjected to prolonged etching HF. Glass Phys Chem 13:247-251.
Carter MC, McIntyre NS, King HW, Pratt AR (1997) The aging of silicate glass surfaces in humid air. J. Non Cryst Solids. 220:127-138. https://doi.org/10.1016/S0022-3093(97)00301-3
Anderson OL (1958) Cooling time of strong glass fibers. J Appl Phys 29:9-12. https://doi.org/10.1063/1.1722953
Paek UC and Kurkjian CR (1975) Calculation of cooling rate and induced stresses in drawing of optical fibers. J Am Ceram Soc 58:330-335. https://doi.org/10.1111/j.1151-2916.1975.tb11490.x
Vikhman SV, Eron'yan MA, Lesnikov PA, Meshkovskii IK, Parfenov PS, Tatarinov EE, Reutskii AA (2019) Morphology of blanks and fiber of guarts glass, Glass Phys Chem 45:589–591. https://doi.org/10.1134/S1087659619060269
Parfenov PS, Eronian MA (2021) Influence of the cooling rate of silica glass on its surface relief. Am J Biomedical Science and Research 13:318-319. https://doi.org/10.34297/AJBSR.2021.13.001879
Vanyushin AV, Petrov VA (1976) Experimental investigation of the spectral absorptance of silica glasses in the wavelength region 0.25–1.25 µm at high temperatures. TVT 14:87-93. High Temperature 14:76–81. https://doi.org/10.2525/ecb1963.14.81
Schultz PC (1974) Optical absorption of the transition elements in vitreous silica. J Am Ceram Soc 57:309-312. https://doi.org/10.1111/j.1151-2916.1974.tb10908.x
Dvurechensky AV, Petrov VA and Reznik VY (1979) Spectral emissivity and absorption coefficient of silica glass at extremely high temperatures in the semitransparent region. Infrared Phys. 19 465-469. https://doi.org/10.1016/0020-0891(79)90060-5
Oh SM (1979) Cooling rates of optical fibers during drawing. Am Ceram Bull. 58:1108-1110.
Aulich H, Douklias N, Eisenrith K-H, Graber K, Kinshofer G, Weidinger F (1980) Influence of preparation conditions on tensile strength of optical fibers. Siemens Forsch-u Entwickl.-Ber. 9:57-64.

No competing interests reported.

Download PDF

Journal Publication

published 29 Dec, 2022

Read the published version in Silicon →

Editorial decision: Major revision
27 Nov, 2022
Reviews received at journal
09 Nov, 2022
Reviewers agreed at journal
08 Nov, 2022
Reviewers invited by journal
07 Nov, 2022
Editor assigned by journal
07 Nov, 2022
Submission checks completed at journal
07 Nov, 2022
First submitted to journal
30 Oct, 2022

You are reading this latest preprint version

Cr2O3 doping effect on silica glass cooling rate

Status:

Journal Publication

Version 1

Abstract

Figures

Introduction

Materials And Research Methods

Results

Discussion

Conclusions

Declarations

References

Additional Declarations

Status:

Journal Publication

Version 1