Corrosion Behaviors of Ni-Cr Alloys in O2 , H2O and H2O+O2 Gases at 700°C and the Effect of Temperature

doi:10.21203/rs.3.rs-3216706/v1

Download PDF

Research Article

Corrosion Behaviors of Ni-Cr Alloys in O2 , H2O and H2O+O2 Gases at 700°C and the Effect of Temperature

https://doi.org/10.21203/rs.3.rs-3216706/v1

This work is licensed under a CC BY 4.0 License

Journal Publication

published 28 Sep, 2023

Read the published version in High Temperature Corrosion of Materials →

You are reading this latest preprint version

Pure nickel and four binary Ni-Cr (5, 10, 20 and 30 wt%) alloys were exposed to Ar-20O₂, Ar-20O₂-20H₂O and Ar-20H₂O (vol.%) at 700°C. In dry/wet O₂, three Ni-Cr alloys (5, 10 and 20 wt%) formed a three-layered structure: an external NiO layer, an inner oxide layer of NiO + Cr₂O₃ and an internal oxidation zone (IOZ) with Cr₂O₃ dispersed. The Ni-30Cr alloy formed a continuous chromia layer, with locally outer NiO islands. In pure water vapor, all alloys underwent internal oxidation, nickel metal expulsion and NiO formation. Compared with the results at 650°C, increasing the temperature to 700°C did not alter the morphology of the oxide scale, but enhanced the scale growth kinetics. A significant difference between these two temperatures was that the strong retarding effect of water vapor on NiO formation in oxygen at 650°C became insignificant at 700°C. However, in water vapor only condition, NiO formation remained much slower at both temperatures. The effects of water vapor and oxygen partial pressure on NiO formation of different alloys and the effect of temperature on scale growth kinetics and morphology were discussed.

Pure nickel

Ni-Cr alloy

Water vapor

Growth kinetics

Morphology

Thermal power is widely used for energy generation in the world. In order to reach higher efficiency, the temperatures of inlet steam can reach 700 ~ 720°C in northern Europe and even higher at 760°C in the USA [1]. Nickel-based alloys are considered as promising construction materials for high temperature components in the next generation of advanced ultra-supercritical power plants, due to a combination of superior corrosion resistance and high creep strength at elevated temperatures [1–3]. A slow growing, continuous and compact oxide scale, commonly Cr₂O₃, is formed to protect the underlying alloys as a barrier from attack in aggressive environments [4, 5].

In our previous study [6, 7], we found that the corrosion rates of Ni-Cr alloys were generally lower in wet O₂/CO₂ or pure water vapor than in dry O₂/CO₂. However, the effect of water vapor on oxidation behavior is complex and depends on the oxygen partial pressure. The addition of H₂O to CO₂ gas not only changes the growth kinetics, but also scale morphology. The continuous NiO layers formed in dry CO₂ were replaced by loose NiO growths and/or scattered Ni metal nodules in wet gas. In contrast, the addition of water vapor to oxygen only slows overall alloy oxidation rates but does not change the scale morphology. Similarly, reduced chromia scale thicknesses in wet O₂ and air compared with those grown in the corresponding dry gases were also found in other investigations [8, 9]. In addition, Ni-Cr alloys developed similar scale morphologies in steam and in wet CO₂: internal oxidation, nickel metal expulsion and external NiO growth, which differed significantly from those frequently observed in oxygen [10]. Latu-Romain et al. [11] found that the inner chromia layer always exhibited n-type semiconduction, while the outer layer shifted from n-type to insulator and finally to p-type semiconduction when oxygen partial pressure was increased.

Although these successes, it is still not clear the effect of water vapor on Ni-Cr alloy oxidation at higher temperatures in the varied pO₂ atmospheres. This work is focused on Ni and Ni-Cr alloy oxidation at 700°C in O₂, O₂ + H₂O and H₂O only gases. The results are compared with those at 650°C reported before [6, 7] to conclude the effect of temperature on corrosion of these materials.

Pure nickel and four model Ni-Cr alloys (Ni-5Cr, 10Cr, 20Cr, and 30Cr) (nominal composition, all in wt%), were made from high purity metals of Ni (99.95%) and Cr (99.995%) by arc melting using a non-consumable tungsten electrode under an Ar-5%H₂ atmosphere. The cast metal and alloy ingots were annealed under a flowing Ar-5%H₂ gas at 1050°C for 50 h for homogenization, and then slowly cooled down to room temperature in the furnace. The annealed alloys were cut into small rectangular plates with the dimensions of (7.5–11.5) mm × (5–8) mm × (0.9–2.5) mm. All surfaces of sample coupons were ground to 1200-grit finish, polished down to 3 µm and then further electro-polished in a hydrochloric solution (17 ml 32 wt% HCl and 23 ml H₂O). The purpose of electro-polishing is to remove the surface work hardened zone created during the sample preparation. All samples were ultrasonically cleaned in ethanol after each step and dried for the reaction. The grain sizes of samples were measured and estimated by using the samples after electro-polishing. The grain exhibits elongated shapes, and the grain sizes are large, around hundreds of microns to several millimeters.

All corrosion experiments were proceeded in a horizontal furnace with an alumina tubular reactor. All samples were exposed to three atmospheres Ar-20O₂, Ar-20H₂O and Ar-20O₂-20H₂O respectively with a linear flow rate of 2 cm/s and a total pressure of 1 atm at 700°C. The reaction time was set at 10, 100 and 300 hours, respectively. The gas flow rates of Ar and O₂ were regulated by rotameters, and water vapor was generated by Ar gas or the mixture of Ar and O₂ passing through a thermostatted water saturator containing demineralized water. The temperature of demineralized water was set to generate excess water vapor which was then condensed inside a condenser with a setting temperature corresponding to the required water vapor content. All samples were fixed on a sample holder in the cold zone of the alumina tubular reactor. Before reaction, the alumina tubular reactor was purged with pure argon for 1 hour to expel air. Then the furnace was heated at a rate of 10°C/min to 700°C and stabilized for 20 minutes. After that, the sample holder was pushed into the hot zone and the reaction gas was introduced subsequently. After the exposure for the desired time, the flowing gas in tubular reactor was changed from reaction gas to pure argon and the sample was pulled out to the cold zone for cooling.

Before and after the reaction, each sample was measured by an analytical balance (Mettler Toledo XP205) with an accuracy of 0.01 mg. The samples after 100 hours of reaction in three different atmospheres were selected to identify the phases of the oxide scales by using X-ray diffractometry (XRD; Empyrean II, Co source). The setting voltage and current were 45 kV and 40 mA, respectively, and the scan angle (2θ) was from 20° to 100°. Cross-sections of reacted samples were characterized by optical microscopy (OM, Nikon 200) and scanning electron microscopy (SEM; FEI Nova NanoSEM 450) equipped with energy dispersive spectroscopy (EDS; Bruker).

3.1 Weight gain kinetics

Figure 1 shows the weight gain kinetics of pure nickel and the Ni-Cr alloys exposed to three different atmospheres at 700°C. In general, weight gain kinetics in dry (Fig. 1a) and wet oxygen (Fig. 1b) were comparable, with the highest rate for Ni-5Cr and the lowest one for Ni-30Cr. In pure water vapor, however, the weight gain kinetics were much lower than those in both oxygen containing gases (Fig. 1c), and the highest weight gains were for Ni-20Cr and 30Cr in this case. For pure nickel, the weight gain kinetics were the lowest in water vapor only condition but much higher than those of Ni-30Cr in both wet and dry O₂ conditions. It should be mentioned that the appearance of weight decreased with reaction time in dry O₂ and H₂O only condition could be related to possible scale spallation.

Assuming diffusion is the controlling step for all situations, the parabolic rate constants of weight gain kinetics, ${k}_{w}$, were calculated by the following equation.

$${\left(\frac{\text{∆W}}{\text{A}}\right)}^{\text{2}}\text{=2}{\text{k}}_{\text{w}}\text{t}$$

where $\text{∆}\text{W}$ is the weight gain, $\text{A}$ is the surface area of tested samples, and $\text{t}$ is the reaction time. The calculated results were summarized in Table 1. The parabolic rate constants for Ni-10Cr in dry oxygen and Ni-30Cr in all three atmospheres were unavailable due to the irregular weight gain. The results showed clearly that the parabolic rate constants of Cr alloys (5-20Cr alloys) in wet oxygen were similar to those in dry oxygen. In pure water vapor, the parabolic rate constants were the lowest in all three environments.

Table 1

Parabolic oxidation rate constants, ${\varvec{k}}_{\varvec{w}}$(10^− 9·g²·cm^− 4·s^− 1), of Ni and Ni-Cr alloys reacted in different environments at 700°C.
Atmospheres	Ni
Ar-20%O₂	4.1	27.1	-	7.7	-
Ar-20%O₂-20%H₂O	5.7	23.4	12.7	6.8	-
Ar-20%H₂O	0.2	0.8	0.4	0.5	-
- Data unavailable due to the irregular weight change

3.2 Reaction product morphology

Figures 2a-c show metallographic cross-sections of pure Ni after exposure at 700°C in the three atmospheres for 100 h. In dry oxygen, a continuous and dense NiO layer with the thickness of approximate 10 µm was formed (Fig. 2a). In wet oxygen, the NiO scale was porous, with numerous pores distributed near the scale-alloy interface. The thickness was similar to that in dry oxygen (Fig. 2b), in line with the weight gain kinetics (Fig. 1b). In pure water vapor, the surface of pure nickel formed a very thin layer after 100 h reaction (Fig. 2c).

Further analysis using BSE-SEM is shown in Fig. 3, which provided more information about the morphology of the scale. The scales formed in both dry and wet oxygen were similar, with numerous pores mainly distributed in the inner part of the scale (Figs. 3a and 3b). In dry O₂, the matrix and the scale were separated by a gap, while in wet oxygen, no such a gap was observed, and the oxide scale kept in a good contact with the alloy. In pure water vapor, however, there was a very thin dense and continuous NiO layer about 1 µm in thickness (Fig. 3c). These oxides were confirmed by XRD analysis (shown in Fig. 2d) to be NiO. After 300 h reaction, the morphologies of pure Ni in three atmospheres remained the same but the thickness increased. The measured thickness of oxide scale in different atmospheres is shown in Table 2.

Table 2

External NiO thicknesses of test alloys after reaction at 700°C in three atmospheres for 300 h (µm).
Atmospheres	Pure nickel	Ni-5Cr		Ni-20Cr
Ar-20O₂	15 (± 2)	13 (± 1)	10 (± 1)	9 (± 1)/ 5 (± 1)
Ar-20O₂-20H₂O	12 (± 1)	12 (± 1)	8 (± 1)	7 (± 0.2)
Ar-20H₂O	3 (± 0.3)	3 (± 0.4)	1.8 (± 0.2)	2 (± 0.2)

Figures 4a-c show the metallographic cross-sections of Ni-5Cr alloy after reaction for 100 h at 700°C in the three atmospheres. Compared with pure nickel in dry oxygen, the oxide morphology was changed significantly when adding 5 wt% Cr. The scale contained a three-layered structure: a top dense and continuous grey layer, an inner layer with some pores, and an internal oxidation zone (IOZ). There were gaps between the outer layer and the inner layer, and the inner layer and the IOZ. Surface X-ray diffraction (Fig. 4d) indicated that the oxide scale was composed of NiO and Cr₂O₃.

Further analysis by the BSE-SEM of the scale and EDS mapping (Fig. 5) indicated that the outer layer was mainly Ni-rich oxide and Cr was detected in the inner layer. According to the SEM image, the IOZ consisted of the needle-like precipitates which were scatteredly distributed in the alloy near the alloy-scale interface. These needle-like precipitates had been identified by TEM and EDS to be Cr₂O₃ in dry oxygen at 650°C [6]. Therefore, the top layer was NiO, followed by NiO and Cr₂O₃ mixture in the inner layer and Cr₂O₃ precipitates in the IOZ. After 300 h reaction, the cross-section morphology did not change much (not shown), and only the scale and IOZ became thicker.

By adding water in oxygen, the morphology did not change too much. The oxide scale (Fig. 4b) consisted of three layers which resembled that in dry oxygen. However, more pores were observed in the inner layer than those in dry oxygen. There were a dense NiO layer on the top, a porous NiO + Cr₂O₃ mixed inner layer, and the needle-like Cr₂O₃ internal precipitates inside the matrix. The XRD results (Fig. 4d) indicated that the components of the oxide scale were the same as those in dry oxygen. After 300 h reaction, the cross-section morphology had no change except the increased thickness (not shown).

When Ni-5Cr alloy was reacted in water vapor only condition, the morphology was changed significantly compared with those in dry and wet oxygen. The scale was much thinner than those in other two atmospheres. Figure 4c shows the metallographic cross-section image of the alloy after 100 h reaction where an IOZ can be observed. Further analysis by XRD indicated that the scale consisted of NiO and Cr₂O₃ (Fig. 4d). High magnification BSE-SEM image shown in Fig. 6a revealed a very thin external layer on the top of IOZ. The EDS point analysis results showed that this thin layer mainly consisted of nickel oxides. Therefore, the scale was composed of an external thin NiO layer and internal Cr₂O₃ precipitates. After 300 h reaction, the morphology was changed compared with that after 100 h reaction (shown in Fig. 6b). The NiO layer was much thicker (about 3 µm) than that after 100 h reaction (0.3 µm). Besides, some metallic Ni islands were visible beneath the NiO layer. The whisker shaped NiO formed on the top of NiO layer, and the IOZ contained both needle-like and fine precipitates. The thickness of IOZ increased significantly.

Figures 7a-c show the metallographic cross-sections of Ni-10Cr after 100 h reaction in the three atmospheres. Similar to Ni-5Cr, in dry and wet O₂, the scale also had three layers which were the outer dense layer, the inner layer with few pores inside and IOZ. The XRD analysis is shown in Fig. 7d, which consisted of NiO and Cr₂O₃, that is, the outer layer was composed of NiO, the inner layer NiO and Cr₂O₃ mixture, and the IOZ with Cr₂O₃ precipitates. The scale thickness in dry and wet oxygen was more or less the same. The only difference was the inner layer formed in wet oxygen had the higher porosity than that in dry oxygen. After 300 h reaction, the morphology in both conditions remained the same (not shown). In pure water vapor, there was an IOZ near the surface in the matrix. Additionally, there were some light-color nodules covered by a dark layer formed on the top of the scale. The oxide scale contained Ni, NiO and Cr₂O₃ identified by XRD analysis (Fig. 7d). The thin top layer covering Ni nodules was NiO and the IOZ was with Cr₂O₃ precipitates. After 300 h reaction, the morphology was changed with a similar structure to that in Ni-5Cr after 300 h reaction. A thin NiO layer was observed with whisker-shaped NiO on the top of the scale, and the IOZ was separated by a metallic Ni layer.

Figures 8a-c show metallographic cross-sections of Ni-20Cr alloy after reaction in the three atmospheres for 100 h. In both dry and wet oxygen, the oxide scale structure was similar with that formed on the surface of Ni-10Cr in the same reaction condition, i.e., the outer light gray NiO layer, inner gray NiO and Cr₂O₃ mixture and internal Cr₂O₃ precipitates. In pure water vapor, the scale structure was also similar with that formed on the surface of Ni-10Cr in the same condition, i.e. the external light-color nodules wrapped by a thin dark oxide layer, and a rather thick internal oxidation zone. The oxide composition of the scale was similar to that of Ni-10Cr, which were NiO and Cr₂O₃ confirmed by the XRD (shown in Fig. 8d).

The metallographic cross-sections of Ni-30Cr alloy in the three conditions are shown in Figs. 9a-c. In dry and wet O₂, the scale consisted of two different contrasts of thin dense layers without any internal oxidation zone observed. The scale was composed of NiO and Cr₂O₃ layers which were confirmed by XRD analysis (Fig. 9d).

A high magnification BSE-SEM image of the scale with EDS mapping is shown in Fig. 10. The mapping results indicated that the outer and inner layers were Ni-rich layer and Cr-rich layer, respectively. Combining these results, the external outer layer was NiO followed by Cr₂O₃ layer. After 300 h reaction, the morphology was similar to that in 100 h reaction.

The metallographic cross-section of the scale in water vapor only condition is shown in Fig. 9c, which consisted of the outer NiO nodules and the IOZ. There was a dense internal Cr₂O₃ band formed beneath the IOZ in contact with the matrix. The scale structure was the same as that of Ni-20Cr alloy in the same condition.

The measured external NiO thicknesses of different alloys after reaction in three atmospheres for 300 h are listed in Table 2. There was not much difference between dry and wet oxygen. The external NiO thickness in water vapor only condition was significantly lower than those in other two atmospheres.

4.1 Effects of water vapor and oxygen partial pressure on NiO formation of pure nickel

As indicated in Figs. 2 and 3, only a NiO scale is formed after reaction of pure nickel in all atmospheres, but its morphology is different. The weight gain kinetics (Fig. 1) and scale thicknesses (Table 2) in both dry and wet oxygen gases are similar. The calculated parabolic rate constants in Table 1 further confirms that there is no significant difference between the oxidation rates of pure Ni in dry and wet oxygen. However, in water vapor only condition, the weight gain kinetics and the scale thickness are significantly lower than those of oxygen-containing gases. Besides, in both oxygen-containing gases, there are some fine pores distributed in the scale (Figs. 3a and 3b). The scale and metal are separated by a gap in dry oxygen (Fig. 3a), but a better scale-metal adherence (no gap) is observed in wet gases (Figs. 3b and 3c). In water vapor only condition, the scale is relatively thin and dense (Fig. 3c).

These observations clearly demonstrate the effects of water vapor and oxygen partial pressure on the oxidation of pure Ni. The effect of water vapor on pure Ni oxidation has been reported previously by several authors [12–14]. The presence of water vapor slows down the oxidation rate due to the preferential absorption tendency of H₂O in NiO [15, 16], leading to the non-acidity of NiO [12]. This non-acidity effect of NiO could be explained by the fact that the bond in OH⁻ is hard to be broken on the surface of NiO scale which results in the low acidity or non-acidity of the scale surface and less oxygen atoms to oxidize the substrate. According to Galerie et al. [12], the NiO formation rate is lower in Ar-H₂O than that in Ar-O₂ at 1100°C when these two gases have the same low oxygen partial pressure. This explains well the observation of much slower NiO formation in water vapor only condition in this work.

By comparing the kinetic results in dry and wet oxygen (Fig. 1, Table 2), the oxidation rates were not affected much by the presence of water vapor in oxygen-containing gases in this work. This result is different from what has been reported in wet O₂ and wet CO₂ at 650°C. Xie et al. [13] observed that the weight gain of pure nickel is 0.76 mg/cm² in dry CO₂, but decreases to 0.06 mg/cm² in wet CO₂ at 650°C for 150 h. Also at this temperature, similar water vapor effects have been observed for pure Ni in oxygen [6]. The rate of NiO formation is substantially decreased in the presence of water vapor, with 0.55 mg/cm² in dry O₂ but very low 0.04 mg/cm² in wet O₂ after 150 h reaction [6]. Clearly increasing temperature to 700°C significantly changes the effect of water vapor in the presence of oxygen which will be discussed in the next section.

Although water vapor does not have much effect on the oxidation rate of pure Ni in the presence of oxygen, it does change the ion diffusion process and mass transfer mechanism. The NiO scale grows in dry oxygen by the dominant outward diffusion of nickel ions via lattice and grain boundaries [17–19]. This could result in the cation vacancies after nickel ions diffuse outward which eventually condense as pores and even gaps (Fig. 3a). The inward oxygen diffusion may also be included in diffusion mechanisms; however, it is much slower than the outward diffusion of Ni ions [4, 17, 20]. In wet gases, the diffusion of ions changes from predominant cation outward diffusion in dry gas to oxygen inward diffusion mixed with the outward diffusion of cations. The presence of water vapor promotes the oxygen inward diffusion and suppresses the outward diffusion of nickel ions [6]. Compared with oxygen, water vapor has the highest priority of absorption tendency [15] which could preferencially occupy grain boundaries and other defects, reducing outward diffusion of nickel ions along the grain boundaries. The faster oxygen inward diffusion results in the inward growth of NiO which increases the adherence of the metal-scale interface as shown in Figs. 3b and 3c. The formation of some pores is attributed to the coalescence of condensed vacancies due to outward cation diffusion in both dry and wet oxygen conditions (Figs. 3a and 3b).

The oxidation of pure Ni is very sensitive to the oxygen partial pressure. In this work, the oxidation kinetics and scale thickness in pure water vapor are significantly lower than that in wet oxygen. The oxide, NiO, is a p-type cation-deficit semiconductor which means there are more nickel ion vacancies generated with the outward diffusion of nickel ions during the oxidation. According to Birks et al. [4], the concentration of cation vacancies is proportional to ${\text{p}}_{{\text{O}}_{\text{2}}}^{\raisebox{1ex}{$\text{1}$}\!\left/ \!\raisebox{-1ex}{$\text{6}$}\right.}$ or ${\text{p}}_{{\text{O}}_{\text{2}}}^{\raisebox{1ex}{$\text{1}$}\!\left/ \!\raisebox{-1ex}{$\text{4}$}\right.}$. In high pO₂ atmospheres (dry and wet oxygen, pO₂ = 0.2 atm), the higher concentration of vacancies than that in water vapor only condition could result in a higher oxidation rate. Therefore, the scale formed in water vapor only condition is thinner and relatively denser due to the slow scale formation rate at low pO₂ atmosphere (pO₂ = 2.4×10^− 8 in water vapor only condition). Unlike at 650°C [6], in the presence of oxygen, the retarding effect of water vapor on Ni oxidation does not exist at 700°C which should be attributed to the effect of temperature.

4.2 Effect of temperature on scale growth kinetics and morphology

As revealed above, water vapor only condition reduces significantly NiO growth kinetics at both 650 [6] and 700°C. However, water vapor effect in the presence of oxygen on NiO formation is quite different with a very slow rate at 650°C but almost no affection at 700°C. This finding indicates that a strong temperature effect on the role of water vapor in the process of nickel oxidation. Nickel oxidation starts from adsorption and dissociation of gaseous oxidants which are water vapor and oxygen in this case. Therefore, there is competitive adsorption and dissociation in the mixed gases. Adsorption and dissociation of water vapor were reported to be more rapid at lower temperatures than for example oxygen, but this difference was less pronounced at higher temperatures [21]. As a result, oxygen is the dominant diffusing species, overwhelming any water vapor effect. This analysis explains well the quite different NiO forming kinetics observed in this work, slow kinetics at a lower temperature 650°C due to dominant water adsorption & dissociation, but high kinetics at a higher temperature 700°C due to dominant oxygen dissolution. The negligible effect of water vapor on NiO formation is further supported by the work of Rahmel [22] at even higher temperatures at 1000°C and 1100°C where water vapor has little effect on the oxidation of pure Ni.

Further kinetic analysis of the external NiO formation of Ni-Cr alloys in both wet and dry oxygen at 650 and 700°C is shown in Tables 2 and 3, respectively. Similar to that for pure Ni, the external NiO formation has been retarded significantly at 650°C but only slightly reduced at 700°C in wet oxygen gas. Similar observation was also reported by Rahmel [22] in his experiment on oxidation of Nimonic 75 (Ni-20Cr) alloy at even higher temperatures at 1000°C and 1100°C. At high temperatures, absorption and dissociation of water vapor are significantly reduced and water vapor effect is no obvious and does not produce a significant change in the oxidation rate. Although this temperature effect is clear, the detailed mechanism of this effect needs further investigation.

Table 3

External NiO thicknesses of test alloys after reaction at 650°C in three atmospheres for 310 h (µm) [7].
Atmospheres	Ni-5Cr		Ni-20Cr
Ar-20O₂	11 (± 1)	9 (± 1)	7 (± 1)
Ar-20O₂-20H₂O	3 (± 1)	2.7 (± 1)	2.3 (± 0.2)
Ar-20H₂O	1.6 (± 0.4)	0.8 (± 0.2)	0.5 (± 0.1)

In spite of this difference, the addition of water vapor to oxygen, in general, did not change the morphology of oxides formed at 650 and 700°C. In dry and wet O₂, for alloys containing 5, 10 and 20 wt% Cr, the scale produced an external NiO layer, internal chromium oxidation and an intermediate zone of NiO + Cr₂O₃ (Figs. 4, 7 and 8, [6]), while the Ni-30Cr alloy formed a continuous chromia layer, with local outer NiO islands (Figs. 9a and 9b). In contrast, in pure water vapor, a thin film of NiO was developed on Ni nodules/layers protruded from the IOZ under the surface of the alloy (Figs. 7c, 8c, 9c). The temperature difference did not change the morphology, but change the scale growth kinetics, which could be well attributed to the different effect of water vapor on NiO forming kinetics. In summary, the water vapor effect not only depends on the oxygen partial pressure, but also the reaction temperature.

Pure nickel and four Ni-Cr alloys with different Cr concentrations were reacted in Ar-20O₂, Ar-20O₂-20H₂O and Ar-20H₂O at 700°C, and the effects of water vapor and oxygen partial pressure on NiO formation of different alloys were investigated and the effect of temperature on scale growth kinetics and morphology was also discussed by comparing with the results at 650°C reported before.

For pure nickel, the weight gain kinetics and scale thicknesses in both dry and wet oxygen gases are similar, but significantly higher than that in water vapor only condition. Water vapor reduced the rate of NiO formation in H₂O-only condition (low pO₂ gas), and led to the formation of a relatively dense NiO scale. Besides, the presence of water vapor accelerated the oxygen inward diffusion rate by diffusing water molecules and hydroxyl ions via grain boundaries. This leads to the inward growth of NiO and better scale-metal adherence in wet gases.

The corrosion performance of different alloys at 700°C is similar with that corroded in the corresponding atmosphere at 650°C in terms of the scale morphology. In both dry and wet oxygen, a typical structure of an external NiO layer, an inner oxide of NiO + Cr₂O₃ and an IOZ was observed for alloys containing 5, 10 and 20 wt% Cr. For Ni-30Cr alloy, a continuous chromia layer, with local outer NiO islands, was formed. In contrast, in pure water vapor, a thin NiO layer was developed on Ni nodules/layers together with an IOZ. The temperature difference did not change the oxide morphology, but changed the scale growth kinetics. At 650°C, NiO formation kinetics were significantly suppressed by water vapor in the presence of oxygen. However, at 700°C, these kinetics were only slightly reduced, probably due to the reduced adsorption and dissolution of water vapor at a higher temperature.

Acknowledgement

Financial support by Australian Research Council under the Discovery Project is highly acknowledged.

Declarations

The authors have no conflicts of interest to declare that relevant to the content of this article.

Abe F. Research and Development of Heat-Resistant Materials for Advanced USC Power Plants with Steam Temperatures of 700°C and Above Engineering. 2015;1:211–224.
Viswanathan R, Bakker W. Materials for ultrasupercritical coal power plants—Boiler materials: Part 1 Journal of Materials Engineering and Performance. 2001;10:81–95.
Viswanathan R, Bakker W. Materials for ultrasupercritical coal power plants—Turbine materials: Part II Journal of Materials Engineering and Performance. 2001;10:96–101.
Birks N, Meier GH, Pettit FS. Introduction to the high-temperature oxidation of metals. City;2006.
Young DJ. Chapter 11 - Effects of Water Vapour on Oxidation. In: Young DJ, ed.^eds. High Temperature Oxidation and Corrosion of Metals (Second Edition), City; Elsevier;2016:549–601.
Jiang C, Xie Y, Kong C, Zhang J, Young DJ. Corrosion behaviour of Ni-Cr alloys in mixed oxidising gases at 650°C Corrosion Science. 2020;174:108801.
Jiang C, Zhang J, Young DJ. The Effect of Water Vapor on NiO Formation by Ni–Cr Alloys at 650°C (HTCPM Focus Issue, FNS-111) Oxidation of Metals. 2021;96:57–68.
Simon D, Gorr B, Christ HJ. Effect of Atmosphere and Sample Thickness on Kinetics, Microstructure, and Compressive Stresses of Chromia Scale Grown on Ni–25Cr Oxidation of Metals. 2017;87:417–429.
Berthod P, Aranda L, Mathieu S, Vilasi M. Influence of Water Vapour on the Rate of Oxidation of a Ni–25wt.%Cr Alloy at High Temperature Oxidation of Metals. 2013;79:517–527.
Wood GC, Wright IG, Hodgkiess T, Whittle DP. A Comparison of the Oxidation of Fe-Cr, Ni-Cr and Co-Cr alloys in oxygen and water vapour. 1970;21:900–910.
Latu-Romain L, Parsa Y, Mathieu S, Vilasi M, Galerie A, Wouters Y. Towards the growth of stoichiometric chromia on pure chromium by the control of temperature and oxygen partial pressure Corrosion Science. 2017;126:238–246.
Galerie A, Wouters Y, Caillet M. The kinetic behaviour of metals in water vapour at high temperatures: Can General rules be proposed? Materials Science Forum, City; Trans Tech Publ;2001:231–238.
Xie Y, Zhang J, Young DJ. Water vapour effects on corrosion of Ni-Cr alloys in CO₂ gas at 650°C Corrosion Science. 2018;136:311–325.
Saunders SRJ, Monteiro M, Rizzo F. The oxidation behaviour of metals and alloys at high temperatures in atmospheres containing water vapour: A review Progress in Materials Science. 2008;53:775–837.
Abellán JP, Olszewski T, Meier GH, Singheiser L, Quadakkers WJ. The oxidation behaviour of the 9% Cr steel P92in CO₂- and H₂O-rich gases relevant to oxyfuel environments. 2010;101:287–299.
Haugsrud R. On the high-temperature oxidation of nickel Corrosion Science. 2003;45:211–235.
Auchi M, Hayashi S, Toyota K, Ukai S. Effect of Water Vapor on the High-Temperature Oxidation of Pure Ni Oxidation of Metals. 2012;78:51–61.
Peraldi R, Monceau D, Pieraggi B. Correlations Between Growth Kinetics and Microstructure for Scales Formed by High-Temperature Oxidation of Pure Nickel. II. Growth Kinetics Oxidation of Metals. 2002;58:275–295.
Kim CK, Hobbs LW. Microstructural evidence for short-circuit oxygen diffusion paths in the oxidation of a dilute Ni-Cr alloy Oxidation of Metals. 1996;45:247–265.
Atkinson A, Taylor RI. The diffusion of 63Ni along grain boundaries in nickel oxide Philosophical Magazine A. 1981;43:979–998.
Larsson K, Björkman H, Hjort K. Role of water and oxygen in wet and dry oxidation of diamond Journal of Applied Physics. 2001;90:1026–1034.
Rahmel A. Einfluss von wasserdampf und kohlendioxyd auf die oxydation von nickel in sauerstoff bei hohen temperaturen Corrosion Science. 1965;5:815–820.

No competing interests reported.

Download PDF

Journal Publication

published 28 Sep, 2023

Read the published version in High Temperature Corrosion of Materials →

Editorial decision: Major revision
28 Aug, 2023
Reviews received at journal
28 Aug, 2023
Reviewers agreed at journal
16 Aug, 2023
Reviewers invited by journal
16 Aug, 2023
Editor assigned by journal
31 Jul, 2023
Submission checks completed at journal
31 Jul, 2023
First submitted to journal
29 Jul, 2023

You are reading this latest preprint version

Corrosion Behaviors of Ni-Cr Alloys in O2 , H2O and H2O+O2 Gases at 700°C and the Effect of Temperature

Status:

Journal Publication

Version 1

Abstract

Figures

1. Introduction

2. Experimental

3. Results

3.1 Weight gain kinetics

3.2 Reaction product morphology

4. Discussion

4.1 Effects of water vapor and oxygen partial pressure on NiO formation of pure nickel

4.2 Effect of temperature on scale growth kinetics and morphology

5. Conclusion

Declarations

References

Additional Declarations

Status:

Journal Publication

Version 1