[1] John JSP, Shanmuganatan MB, Kiran VS, Kumar S, Krishnamurthy R (2019) Investigation of friction stir processing effect on AA 2014-T6. Materials and Manufacturing Processes 34:159-176
[2] Patel V, Li W, Xu Y (2019) Stationary shoulder tool in friction stir processing: a novel low heat input tooling system for magnesium alloy. Materials and Manufacturing Processes 34:177-182
[3] Kumar KA, Natarajan S, Duraiselvam M, Ramachandra S (2019) Synthesis, characterization and mechanical behavior of Al 3003-TiO surface composites through friction stir processing. Materials and Manufacturing Processes 34:183-191
[4] Mishra RS, Ma ZY(2005) Friction stir welding and processing. Materials Science and Engineering: R: Reports 50:1-78
[5] Thankachan TK, Prakash S, Kavimani V (2018) Effect of friction stir processing and hybrid reinforcements on copper. Materials and Manufacturing Processes 33:1681-1692
[6] Parikh VK, Badgujar AD, Ghetiya ND (2019) Joining of metal matrix composites using friction stir welding: a review. Materials and Manufacturing Processes 34:123-146
[7] Liu G, Murr L, Niou C, McClure J, Vega F (1997) Microstructural aspects of the friction-stir welding of 6061-T6 aluminum. Scripta Materialia 37:355-361
[8] Bajakke PA, Malik VR, Deshpande AS (2019) Particulate metal matrix composites and their fabrication via friction stir processing - a review. Materials and Manufacturing Processes 34:833-881
[9] Goel P, Khan NZ, Khan ZA, Ahmari A, Gangil N, Abidi MH, Siddiquee AN (2019) Investigation on material mixing during FSW of AA7475 to AISI304. Materials and Manufacturing Processes 34:192-200
[10] Mahoney M, Rhodes C, Flintoff J, Bingel W, Spurling R (1998) Properties of friction-stir-welded 7075 T651 aluminum. Metallurgical and Materials Transactions A 29:1955-1964
[11] Elangovan K, Balasubramanian V (2007) Influences of pin profile and rotational speed of the tool on the formation of friction stir processing zone in AA2219 aluminium alloy. Materials Science and Engineering: A 459:7-18
[12] Xiong JT, Li JL, x Qian JL, Zhang FS, Huang WD (2012) High strength lap joint of aluminium and stainless steels fabricated by friction stir welding with cutting pin. Science and Technology of Welding and Joining 17:196-201
[13] Kimapong K, Watanabe T (2004) Friction stir welding of aluminum alloy to steel. Welding Journal 83:277-282
[14] Asemabadi M, Sedighi M, Honarpisheh M (2012) Investigation of cold rolling influence on the mechanical properties of explosive-welded Al/Cu bimetal. Materials Science and Engineering: A 558:144-149
[15] Lee JS, Son H, Oh I, Kang C, Yum CH, Lim SC, Kwon HC (2007) Fabrication and characterization of Ti–Cu clad materials by indirect extrusion. Journal of Materials Processing Technolgy 187:653–656
[16] Li X, Zu G, Ding M, Mu Y, Wang P (2011) Interfacial microstructure and mechanical properties of Cu/Al clad sheet fabricated by asymmetrical roll bonding and annealing. Materials Science and Engineering: A 529:485-491
[17] Shen Z, Chen Y, Haghshenas M, Nguyen T, Galloway J, Gerlich AP (2015) Interfacial microstructure and properties of copper clad steel produced using friction stir welding versus gas metal arc welding. Materials Characterization 104:1-9
[18] Leitao C, Arruti E, Aldanondo E, Rodrigues DM (2016) Aluminium-steel lap joining by multipass friction stir welding. Materials & Design 106:153-160
[19] Zheng Q, Feng X, Shen Y, Huang G, Zhao P (2016) Dissimilar friction stir welding of 6061 Al to 316 stainless steel using Zn as a filler metal. Journal of Alloys and Compounds 686:693-701
[20] Li B, Shen Y, Luo L, Hu W (2016) Effects of processing variables and heat treatments on Al/Ti-6Al-4V interface microstructure of bimetal clad-plate fabricated via a novel route employing friction stir lap welding. Journal of Alloys and Compounds 658:904-913
[21] Fari A, Batalha GF, Prados EF, Magnabosco R, Delijaicove S (2013) Tool Wear Evaluations In Friction Stir Processing Of Commercial Titanium Ti-6Al-4V. Wear 302:1327-1333
[22] Ma ZY, Mishra RS, Mahoney MW (2002) Superplastic deformation behaviour of friction stir processed 7075Al alloy. Acta Materialia 50:4419-4430
[23] Hammerschmidt M, Kreye H (1981) Microstructure and bonding mechanism in explosive welding. In: Meyers MA, Murr LE (Eds) Shock Waves and High-Strain-Rate Phenomena in Metals,1st ed. Springer, Boston, pp 961-973
[24] Yang B, Yan J, Sutton MA, Reynolds AP (2004) Banded microstructure in AA2024-T351 and AA2524-T351 aluminum friction stir welds: Part I. Metallurgical studies. Materials Science and Engineering: A 364:55-65
[25] Hunt JN (1968) Wave formation in explosive welding. The Philosophical magazine 17:669-680
[26] Humphreys FJ, Prangnell PB, Priestner R (2001) Fine-grained alloys by thermomechanical processing. Current Opinion in Solid State and Materials Science 5:15-21
[27] Mendez PF, Tello KE, Lienert, TJ (2010) Scaling of coupled heat transfer and plastic deformation around the pin in friction stir welding. Acta Materialia 58:6012-6026
[28] Arora A, Zhang Z, Deb A, Debroy T (2009) Strains and strain rates during friction stir welding. Scripta Materialia 61:863-866
[29] Bang H, Bang H, Jeon G, Oh, I, Ro C (2012) Gas tungsten arc welding assisted hybrid friction stir welding of dissimilar materials Al6061-T6 aluminum alloy and STS304 stainless steel. Materials & Design 37:48-55